Month: May 2013
Douglas Lake is flooding
The water can’t get much higher before it starts going over the dam. In the meantime water levels are wreaking havoc. Here my floating dock is pulled as high as I thought it would ever need to be. I would have to detach it from my winch cable and move it higher. I probably won’t because the lake will drop again as soon as TVA is able to lower it without more flooding down stream.
Some of my neighbors are having a tougher time though.
This is my next door neighbor’s dock. I tried moving that tree but I’ll have to wade in to get enough leverage. It’s very large and mostly waterlogged. That makes it really heavy. Yesterday afternoon a large float of debris washed up our little cove. The far end must be several feet deep in debris. Several dead animals are floating in the mess too.
Farther down is more debris trapped by a floating dock. Beyond that is a neighbor’s DECK that’s been covered. Their floating dock is still working though.
Taking a closer view. You’d have to swim to the ramp and wade across that to get to the dry floating dock.
Irises going nuts
Looking at our pretty irises and seeing the extremely high lake levels in the background.
Sunset
Smokin in a Brinkman vertical smoker
I bought a cheap(ish) smoker on Craigslist and set it up to smoke a Boston Butt. This one runs on charcoal and I tossed plenty of hickory chips into the pan with the charcoal. Turns out maintaining a temperature is harder than it should be with this model. It didn’t help that it was cold and rainy out.
After 9 hours in this smoker I gave up and tossed it into the oven to finish. The smoky flavor is pretty good but I’ve done better with my propane grill.
Rescued turtle.
Driving home I spotted something in the road. Of course I aimed to miss it so it had my attention. When I realized it was a turtle I stopped and picked it up. This little guy swam as hard as he could for the entire drive to my house. So I set him down near the lake and suddenly he got shy. I picked him up again and he popped right out and started swimming again. I set him down just a couple of inches from the water. This time he saw the water and climbed into the lake and swam away. I predict he’ll be pretty happy there. Certainly better than found on road dead.
Ceramic coated exhaust manifold
While doing some work on Nat’s 1968 Camaro I had to take the exhaust manifolds off. While I had them off I used a grinder and some files to clean up the mold flash. Once cleaned up I took them out to be ceramic coated. The coating not only makes them look better but it also keeps heat contained and sends it out the exhaust to the pipes.
This is the passenger side bolted in place.
This is the driver’s side. They don’t stand out except as clean. I like it.
New water pump and thermostat
I decided that if I didn’t replace the water pump now I’d be doing it soon after getting the car back on the road. At least now it’s easy to get to. Corrosion in the heater core and radiator along with “mud” coming out of the cooling system convinced me that the coolant had failed in its anti corrosive properties. It would have been nice to flush the motor with the water pump off but there were no exhaust manifolds and no spark plugs then. Don’t want water inside the motor.
The water pump I took off was painted Chevy engine orange to match the engine so I did the same with this one. I looked into switching to a clutch type fan but wasn’t ready to spend the $270 or more it would take. If I decide to make a change in the future I’ll probably hide an electric fan in the fan shroud so it appears more stock.
New motor mount
I wish I’d had this view of things when I replaced the motor mounts. There had been some odd things with launching the car from a stop that I decided were because the motor was torquing on its mounts. The Camaro uses a mechanical belcrank setup between the frame and the block. While the motor mounts were in better shape than I thought they weren’t bolted down properly.
Unfortunately I’ve found another potential culprit in the subframe bushings and/or their mounting points.
Heater box on outside of firewall
